您好,小程序模板欢迎您。
小程序模板
当前位置 : 首页> 小程序教程> 微信小程序倒计时组件开发

微信小程序倒计时组件开发

先来看下最终效果:

0.gif

git源:http://git.oschina.net/dotton/CountDown

分步骤-性子急的朋友,可以直接看最后那段代码。

wxml文件放个text

second: {{second}} micro second:{{micro_second}}

在js文件中调用

function countdown(that) {  var second = that.data.second  if (second == 0) {    // console.log("Time Out...");
    that.setData({
      second: "Time Out..."
    });    return ;
  }  var time = setTimeout(function(){
    that.setData({
      second: second - 1
    });
    countdown(that);
  }
  ,1000)
}

Page({
    data: {
        second: 3
    },
    onLoad: function() {
        countdown(this);
    }
});

运行验证下,从10走到1s,然后显示时间到。

于是继续将毫秒完善,注意毫秒的步长受限于系统的时间频率,于是我们精确到0.01s即10ms


js

/* 秒级倒计时 */function countdown(that) {  var second = that.data.second  if (second == 0) {
    that.setData({
      second: "Time out!",
      micro_second: "micro_second too."
    });
    clearTimeout(micro_timer);    return ;
  }  var timer = setTimeout(function(){
    that.setData({
      second: second - 1
    });
    countdown(that);
  }
  ,1000)
}/* 毫秒级倒计时 */// 初始毫秒数,同时用作归零var micro_second_init = 100;// 当前毫秒数var micro_second_current = micro_second_init;// 毫秒计时器var micro_timer;function countdown4micro(that) {  if (micro_second_current <= 0) {
    micro_second_current = micro_second_init;
  }
  micro_timer = setTimeout(function(){
    that.setData({
      micro_second: micro_second_current - 1
    });
    micro_second_current--;
    countdown4micro(that);
  }
  ,10)
}

Page({
    data: {
        second: 2,
        micro_second: micro_second_init
    },
    onLoad: function() {
        countdown(this);
        countdown4micro(this);
    }
});

wxml文件

second: {{second}}s{{micro_second}}


如此,当秒级运行完毕时,毫秒级timer即clearTimeout,并将字本显示为'micro_second too'

再添加一个countdown4micro方法,使得显示剩余 0:3:19 89这样形式的倒数


function dateformat(second) {    var dateStr = "";    var hr = Math.floor(second / 3600);    var min = Math.floor((second - hr * 3600) / 60);    var sec = (second - hr * 3600 - min * 60);// equal to => var sec = second % 60;
    dateStr = hr + ":" + min + ":" + sec;    return dateStr;
}


目前有2个时钟,影响性能,合并下去掉countdown,于是countdown4micro变成以下的样子:

function countdown4micro(that) {    var loop_second = Math.floor(loop_index / 100);    // 得知经历了1s
    if (cost_micro_second != loop_second) {        // 赋予新值
        cost_micro_second = loop_second;        // 总秒数减1
        total_second--;

    }      // 每隔一秒,显示值减1; 渲染倒计时时钟
    that.setData({
      clock:dateformat(total_second - 1)
    });      if (total_second == 0) {
        that.setData({          // micro_second: "",
          clock:"时间到"
        });
        clearTimeout(micro_timer);        return ;
      }    

  if (micro_second_current <= 0) {
    micro_second_current = micro_second_init;
  }
  micro_timer = setTimeout(function(){
    that.setData({
      micro_second: micro_second_current - 1
    });
    micro_second_current--;    // 放在最后++,不然时钟停止时还有10毫秒剩余
    loop_index ++;
    countdown4micro(that);
  }
  ,10)
}

如此这般,毫秒与时分秒是分别运行渲染的,再次改造,程序可读性更好。dateformat针对于毫秒操作,而不接受秒为数。同时还省却了计算100次为1s的运算

/** 
 * 需要一个目标日期,初始化时,先得出到当前时间还有剩余多少秒
 * 1.将秒数换成格式化输出为XX天XX小时XX分钟XX秒 XX
 * 2.提供一个时钟,每10ms运行一次,渲染时钟,再总ms数自减10
 * 3.剩余的秒次为零时,return,给出tips提示说,已经截止
 */// 定义一个总毫秒数,以一分钟为例。TODO,传入一个时间点,转换成总毫秒数var total_micro_second = 2 * 1000;/* 毫秒级倒计时 */function countdown(that) {      // 渲染倒计时时钟
      that.setData({
          clock:dateformat(total_micro_second)
      });      if (total_micro_second  var sec = second % 60;
    // 毫秒位,保留2位
    var micro_sec = Math.floor((micro_second % 1000) / 10);    return hr + ":" + min + ":" + sec + " " + micro_sec;
}

Page({
    data: {
        clock: ''
    },
    onLoad: function() {
        countdown(this);
    }
});


经过如上优化,代码量减少一半,运行效率也高了。

联系客服 意见反馈

签到成功!

已连续签到1天,签到3天将获得积分VIP1天

知道了